Tips for running Kubuntu 9.04 (Jaunty) on an EeePC 901go [update3]
April 23, 2009
It has been a long time since my last post, but with my house building project time is short. But I found time to upgrade my Netbook from Kubuntu 8.10 to Kubuntu 9.04. The reason I was so eager to get the new version up and running are the graphics problems with 8.10 (poor graphics performance and rendering errors). Please take a look at my Post about Kubuntu 8.10 on my EeePC, as most of the stuff is still valid. I’ll write in this post only what I did differently.
- At the time of writing this (23.4.2009) it is necessary to install a custom kernel to activate UXA for your netbook. I used following howto to install the latest testing kernel 2.6.30-rc2 and updated drm and xserver packages. With these changes I don’t have rendering errors and the performace for the KDE 3D effects is ok. A short look at flash videos also shows that they are also ok, but I’ll take a closer look at videos in the next days and at it to this post.
- I did not install a special EeePC kernel so far as with Kubuntu 8.10. At the time of writing there seems to be also no Update to the Array Kernels and packages for Jaunty anyway. [Update] There is now but I’ll stay with the 2.6.30-rc2 for the time being. [/Update]
- I’v upgraded my script for installing additional packages for Kubuntu. Here is the file.
- I installed
eee-applet
which comes as Jaunty packages, but it didn’t work. [Update] I searched further and installed the Jaunty package from here. You need to install these packages (apt-get install python-gconf python-notify python-pyorbit) before installing the package like this: dpkg -i eee-control_0.9.0_all~jaunty.deb [/Update]
Sofar everything seems to run nicely. Anyway I’ll update this blog post if I find a problem or come up with an solution.
[Update]
- The WLAN stuff does do seem to have the same performance problems (=hangs) as with the Kubuntu 8.10 kernel. I’ll take a look at the way I solved the problem with the old kernel and try to do the same here. I’ll keep you posted.
[Update2]
- The problem with the Wifi is not as bad as with intrepid, as I don’t have packet loss. Maybe it is also a compatibility problem with my access point.
- I did forget to post the MRRT stuff I changed or better not changed according to the howto. Here is it:
lspci -vvnn
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7f00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at dc80 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f7ec0000 (32-bit, non-prefetchable) [size=256K]
Capabilities:
Kernel modules: intelfb
cat /proc/mtrr
reg00: base=0x000000000 ( 0MB), size= 2048MB, count=1: write-back
reg01: base=0x07f800000 ( 2040MB), size= 8MB, count=1: uncachable
reg02: base=0x0d0000000 ( 3328MB), size= 256MB, count=1: write-combining
You see that the prefetchable memory is at d0000000 and with an size of 256 MByte. (As Info: 256MB = 0x10000000). Therefore our MTRR line is
echo "base=0xd0000000 size=0x10000000 type=write-combining" >| /proc/mtrr
As you see I’ve this line already, so no need for me to add it.
[Update3]
- As it seems the ath5k driver for the WLAN is still not as good as the madwifi driver. I installed it like this. Go do
http://snapshots.madwifi-project.org/madwifi-hal-0.10.5.6/
and download the newest version there. In my case I did following:wget http://snapshots.madwifi-project.org/madwifi-hal-0.10.5.6/madwifi-hal-0.10.5.6-r4016-20090429.tar.gz
Now extract it:
$ tar xzfmadwifi-hal-0.10.5.6-r4016-20090429.tar.gz
$ cd madwifi-hal-0.10.5.6-r4016-20090429
Now we need some packages installed:
sudo apt-get install build-essential
And now the actual compiling and installation
cd scripts
sudo ./madwifi-unload
sudo ./find-madwifi-modules.sh $(uname -r)
cd ..
sudo make
sudo make install
At last we need to add
blacklist ath5k
to/etc/modprobe.d/blacklist-eeepc
and appendath_pci
to/etc/modules
. After a reboot you should have a better working WLAN. - As of now I’ve an idle power consumption under 11 Watt, most of the time at 10.4 Watt. I’ve changed following in addition to the above stuff. I’m using powertop (apt-get install powertop) to take a look what could be improved.:
- echo 1500 > /proc/sys/vm/dirty_writeback_centisecs
- Enable USB Suspend
- disable HAL polling
No Comments yet »
RSS feed for comments on this post. TrackBack URI
Leave a comment
Powered by WordPress
Entries and comments feeds.
Valid XHTML and CSS.
34 queries. 0.050 seconds.